Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Electric operated thermic fluid heaters are designed and manufactured using high quality heating elements, precise dimensions in a state of the art manufacturing facility. Our quality control guarantees highest safety and tong life span. Electrical energy offers various advantages in process heating.
HC-1 Thermal Fluid Heaters The HC-1 thermal fluid heater is available in standard sizes from 1 to 30 MM Btu/hr. Configuration options include vertical up-fired, vertical down-fired, and horizontal. Custom heater designs are also available to meet a wide variety of project-specific design challenges.
3 tph gas fired boiler - Gas Fired Boiler. 8 tph boiler D-type Boiler in Albania Small Biomass. 5 tph gas fired boiler 5 tph oil gas fired diesel boiler by biomassfiredboiler on July 17, 2018 in Vertical Biomass Boiler Quick inquiry: I need the quotation of Pls Select Product Thermal oil Boiler Electric Boiler Steam Boiler Hot Water Boiler Hot Air Boiler
Consider a properly designed installation from the start, with thermal fluid according to your needs, but be very careful in the selection of a pump change for any circumstance, as cracking can be caused by a lack of thermal fluid flow in the boiler.For any modification or extension of the initial circuit, resort to a professional hydraulic
Thermal fluid heating systems use indirect methods for heating a substance or system. The heater is used to heat an intermediate liquid (often water, thermal oil or glycol). This intermediate liquid is then used to transfer heat to the end target. The end target can be process equipment, or other liquids during transfer or while […]
Carl Gustav Carus University Hospital in Dresden charges BBS GmbH with supply of two (2) Thermal Fluid Heater HG 700. The Thermal Fluid plant is served as primary power source for the generation of pure steam. The pure steam is required for the sterilization machine and air conditioning of sterilization rooms. Technical data HG 700 […]
American Heating Company is the acknowledged leader in the technology of packaged thermal fluid heaters and hot oil heaters.We are proud to be the only heater company in this market to offer a serpentine radiant coil unit as the standard in our industrial thermal fluid heater design.
Thermal Fluid vs. Steam A thermal fluid (hot oil) system operates in a closed loop circulation system with minimal pressure. Fulton thermal fluid systems can reach 750°F (345°C) making them an ideal choice for many process heat applications. The choice between a steam system or a thermal fluid system is governed by the process requirements.
Fulton’s thermal fluid heaters feature a four-pass, high-efficiency design that pre-heats combustion air. Their compact construction can, like many Fulton systems, be skid-mounted with ancillaries; and includes models with heat outputs to 3500kW and standard operating temperatures of 345°C (400°C is also available with optional heater
SAZ BOILERS is an ISO 9001:2008 Certified Company. We are one of the prominent manufacturer, exporter, and supplier of Thermal Fluid Heaters, Steam Boilers, Hot …
Diesel Fired Thermal Fluid Heater Installation in Russia Customer Factory Company Profile Romiter Group Limited are committed to manufacturing and exporting complete enery saving heating equipment, including thermal oil boiler (Thermal fluid heat transfer product), thermal …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292
Get Latest PriceCopyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.