Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
File Size: 95KB facility either set or limit the range of operating pressure of the boiler. 2. Determine the steam load characteristics and ultimately the profile of the steam-use facility in its entirety (see Section I1). It is important to understand both the steady-state load profile …
How an industrial boiler system works The heart of an industrial boiler system is a hot water or steam boiler operated with a certain kind of fuel. The boiler heats up or evaporates the water inside it, which is then transported to the consumers via pipe systems. In case of hot water the transport energy is …
Author: Bob Formisano As shown in the diagram, the boiler risers should always be at least 24 in. long and the steam supply should always be piped between the last boiler riser and the equalizer. The NBP should also include a Hartford Loop, which consists of an equalizing pipe connecting
File Size: 258KB Superheated steam is steam at a temperature higher than the saturation temperature corresponding to pressure. For example, a boiler may operate at 415 psig (pounds per square inch gauge). The corresponding saturation temperature for this pressure is 483°F, and this will be the temperature of the water in the boiler and the steam in the drum.
File Size: 1MB and critical for normal boiler service life and correct operation. This is water free of excessive minerals and gases with a nominal pH of 7.8 ± 0.5. A pH reading of around 10.0 or higher can result in priming and surging, which can cause wet steam and/or flooding of the steam supply and steam header. A pH level only a single digit away from
Internal inspections are required on steam boilers that have hand hole or manhole openings. A hand hole is a small oval port just large enough to get your hand, and in some cases your arm, inside the boiler to allow for a visual inspection of the water side of boiler and aid in the cleanout of mud and sludge from the waterside of the boiler.
Mar 04, 2020· There are different components present in feed water and steam circuit of boiler and we should know some essential components of these circuit and these are Economizer, boiler drums, water tubes, and super heater.. Economizer. Economizer is a heat exchanger which takes heat from the flue gas, and increases the temperature of feed water coming from feed water common header to about …
2.4.5 Perform a life cycle cost analysis of purchased steam versus VA-generated steam including all expense factors such as boiler plant investment, fuel cost, salaries of operating personnel, maintenance costs, and electricity and water costs.
Simple vertical boiler and Cornish boilers are single tube boilers. Multi Tubular Boiler. In a multi-tubular steam boiler, there are two or more fire tubes or water tubes. Stationary Boiler. These boilers are mainly used in power plants, and in industrial process work. These are called stationary because they do not move from one place to another.
Dec 11, 2017· Steam Boiler Diagram With Parts for Dummy’s. By MS Chaudhry | December 11, 2017. 1 Comment. Below is a typical steam boiler diagram for dummy’s to understand with name of each component or boiler part. First of all you should understand …
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.