Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Heat absorbed by water = 0.95 Vs(t 1 − t 2)MJ s −1,. t 1 and t 2 = temperature of hot gases before and after the W.H. boiler, °C.. Total heat as steam = sensible heat in feed water + heat absorbed by water in boiler. In good practice t 2, the temperature at which the flue gases leave the boiler, may be reduced to ca.50 K above the temperature of the water in the boiler.
File Size: 1MB Air intake and exhaust openings for make-up/combustion air and ventilation of waste heat from the radiator are required for operation of the generator. Fire-smoke dampers, required by OSSC table 716.5, would prevent combustion air from entering the generator enclosure thus disabling the generator.
CO Boilers for the world’s major Fluidized Catalytic Cracking Unit (FCCU) process licensors. CO Boilers are thermal oxidizers with integral waste heat recovery systems that are used to oxidize carbon monoxide-rich waste gases typically generated by Fluidized Catalytic Cracking Units (FCCU) in petroleum refineries. They are traditionally referred
Waste Heat Recovery Boiler - Waste Heat Boiler - Waste heat boilers are the significant energy saving equipment, utilize the heat in flue gases from combustion processes or hot extract air from industrial processes to generate hot water or saturated steam Otherwise, the waste heat boiler could be used in oil gas fired combined cycle units, and take advantage of the high temperature flue gas
RENTECH Boiler Systems offers a full range of custom designed waste heat recovery boiler systems to meet your most demanding project requirements. RENTECH is an American boiler manufacturer known for its ability to provide custom engineered solutions for a wide variety of applications.
The Incline HRSG reclaims waste heat from a Centaur 40 gas turbine and supplies 19,200 PPH / 135 PSIG steam to the prison for heating and process users. The boiler and auxiliary equipment were delivered and were successfully started up.
A significant amount of waste heat in flue gases remains untapped due to the limited applicability of metal heat exchangers under conditions where acid dew point corrosion can occur. The HeatMatrix polymer heat exchanger overcomes this limitation and enables energy savings by up to 5% in combustion processes and even up to 25% on dryers.
119 Cimarron Park Loop, Suite A Buda, Tx, United States 78610 The Claus Waste Heat Boiler (WHB) is a critical piece of equipment in a Sulphur Recovery Unit (SRU); its fundamental purpose is as a heat transfer device used in energy recovery.
Jan 01, 2013· The ASME Boiler and Pressure Vessel Code (ASME BPVC), which is administered by ASME (New York, N.Y.; www.asme.org; founded as the American Society of Mechanical Engineers), is a well-established standard for the design and fabrication of boilers and pressure vessels.ASME code-symbol stamps show compliance with the requirements of the standard, but code stamping of steam …
With up to 500,000 lb/hr of steam flow, our waste heat boilers significantly reduce fuel and energy expenses, as well as greenhouse gas emissions.
Apr 17, 2020· A waste heat boiler of the water-tube design is able to cope with much higher pressures of steam than a fire-tube boiler, but it is more difficult to construct and install. Inside this type of boiler, there are narrower tubes than inside a fire-tube boiler, and the tubes contain water instead of hot gases.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292
Get Latest PriceCopyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.