Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Jul 01, 2011· The CO combustor with boiler is used to oxidise the CO to CO2 to meet environmental regulations while facilitating the recovery of valuable energy from the flue gas. Combustion air and fuel control The combustion air control scheme for a CO boiler is fundamentally different from that of a conventional industrial steam generating boiler.
Boiler Three Element Controller Philosophy A single element control system is one with just one control input, a two element control system is one with two control inputs, etc. A three-element boiler water level control system is one which typically uses the measured water level, the steam flowrate from the boiler, and the water flowrate into
In multiple boiler installations, the burner management systems of each boiler may be controlled by a master plant controller (sometimes referred to as a lead-lag controller) to stage boiler operation to minimize on/off operation. They may also minimize frequent burner cycling, which can cause thermal stresses leading to tube and tube sheet leaks.
Hot Water Boiler Sequence of Operation Aquastats - As boilers go, there is not a single sequence of operation for any hot water boiler out there, but there is a typical sequence of operation for most boilers. We will start off describing the typical hot water boiler without domestic hot …
The National Board of Boiler and Pressure Vessel Inspectors was created in 1919 to promote greater safety to life and property through uniformity in the construction, installation, repair, maintenance, and inspection of pressure equipment.
boiler opration controller. ZOZEN is a world-leading provider of boilers and industrial boiler solutions
Control of Boiler Operation using PLC – SCADA K. Gowri Shankar Abstract––This paper outlines the various stages of operation involved in the conversion of a manually operated boiler towards a fully automated boiler. Over the years the demand for high quality, greater efficiency and automated machines has increased in this globalised world.
Boiler control systems custom engineered by U.S. Boiler Company enhance heating system efficiencies and help provide homeowners with both energy and cost savings. Not only will our innovative control systems help you maximize efficiencies, improve system performance, and enhance comfort, but they'll also help you save money.
Boiler controls provide that extra level of power over your heating systems. These devices perform a number of activities like timing, programming, monitoring and adjusting. Boiler controls can improve energy efficiency and boost your system's overall performance.
When the temperature of the water reaches the set point of main boiler controller the ignition control closes the gas valve and the main burners shut down. The inducer or forced draft fan motor continues to run for a period of time so that all the combustion gases in the system are purged up through the boiler flue or boiler stack .
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.