Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Kg/H · Pressure Drop in Steam Pipes Name Description Boiler Replacement Guide Step-By-Step Procedures For Properly Sizing Hot Water And Steam Replacement Boilers For Homes And Small Commercial Buildings Easy-Loop Booklet Simplified Procedures For Designing An Easy-Loop Hydronic Heating System Using Weil-McLain® Boilers, Convector Baseboard, And Series-Loop Piping
Apr 30, 2019· BTUh simply refers British Thermal Units per hour. For instance, if you are looking at a boiler with a rating of 80,000 BTUh, you can safely assume that the unit’s gross output is 80,000 BTUs, or 80 MBH (one MBH = 1,000 BTUh).
Example: the size from the previous chart is 60 gallons and we have no temperature limitations. We will use a standard LI-60, insulated kettle with a maximum steam flow rate at 30 psi of 140 lbs. We are delivereing 150,000 Btu (145,500 lbs. of steam) by using a boiler with 300,000 Btu input and 50% efficiency note: these are reasonable numbers
New England Kiln Drying Association – Steam Design & Best Practices – HerLine Technologies Steam Distribution System Proper layout design & pipe sizing of mains Piping always pitched in the direction of flow Use of eccentric reducers to eliminate creation of condensate collection points (low spots) in piping
Dec 05, 2017· Next, compare this to the color brochure for the steam boiler and choose the boiler that meets the required load. An important note on boiler sizing – all the supply piping in the basement should be insulated with a minimum of 1” of pipe insulation. A better choice would be 1 …
BOILER REPLACEMENT GUIDE INTRODUCTION This booklet is designed to give the quality-conscious hydronic heating contractor a step-by-step procedure for properly sizing hot water and steam replacement boilers. It is intended primarily for use in sizing boilers for homes, but in many cases can also be used for small commercial buildings.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292
Get Latest PriceCopyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.
