Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
which power plant does not need boiler. which power plant does not need boiler. Thermal power station - Wikipedia. A thermal power station is a power station in which heat energy is converted to electric power.In most of the places in the world the turbine is steam-driven.Water is heated, turns into steam and spins a steam turbine which drives an electrical generator.After it passes
Jan 30, 2018· Ultimately, we need power plants to start disclosing their water-use data directly. This methodology provides a stand-in in the meantime. Once all thermal power plants — and someday, all water users — disclose their usage, we can take more meaningful and targeted steps to addressing growing water stress.
Author: EnConNetwork Haycock and wagon top boilers. For the first Newcomen engine of 1712, the boiler was little more than large brewer's kettle installed beneath the power cylinder. Because the engine's power was derived from the vacuum produced by condensation of the steam, the requirement was for large volumes of steam at very low pressure hardly more than 1 psi (6.9 kPa) The whole boiler was set into brickwork
The steam condenser of a power plant boiler is a critical heat exchanger in the process. Poor performance due to restricted heat transfer can have a dramatic influence on unit efficiency.
Jan 07, 2017· Need condensing turbine vacuumize before cold startup. In this article we discussed about the importance of building vacuum inside the turbine during cold start up of turbine and what the problem could be occurred if we are not vaccumize the turbine.There are much air inside the turbine before cold start, if the vaccumize procedure does not performed.
Boilers are used in power plants in order to produce high pressured steam, so that the plant can generate electricity.The process that does this is known as the Rankine cycle.The boiler takes in energy from some form of fuel such as coal, natural gas, or nuclear fuel to heat water into steam.All but a small fraction of the world's primary energy comes from fuels, and about three-quarters of
Author: Learn Engineering The plant has not been used to produce electricity for about 18 months, and for about a year a smaller rental boiler has been producing the steam needed for district heat. The commission met in a
Types of Boilers Used in Power Plants 2017-07-31 17:31:22 . A power plant or a power generating station, is basically an industrial location that is utilized for the generation and distribution of electric power in mass scale, usually in the order of several 1000 Watts.
Author: Shelby Lindrud Boiler metal temperature increases when it is heated up. The increase in temperature of the boiler meal causes an expansion. So some degree of freedom for expansion need to be provided. In case , Boiler is restrained fully, heated boiler metal wil
A boiler is a closed vessel in which fluid (generally water) is heated. The fluid does not necessarily boil.The heated or vaporized fluid exits the boiler for use in various processes or heating applications, including water heating, central heating, boiler-based power generation, cooking, and sanitation
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.