Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
The Boler Body – can tell you a lot about the condition of the frame. Since the bodyshell is made from molded fiberglass it lasts a lifetime and can be repaired, but think of the body as a box, if you take it by the ends and twist it the shape will deform, we are looking for this and then what is …
1. The main parts you'll need for this build can be changed wildly depending on your available materials. I picked up most of my parts from my loca2. First you will need a small soup can and a drill bit just slightly smaller then the tubing you plan to use. In this step we will drill 2 holes i3. Once you have the contents of your can removed you will drill the 3rd hole to work as the filling hole. I chose to use a small brass fitting and4. At this stage you can cut a small section of tubing and feed it into the sight glass holes. Clean up any remaining glue reside from the can as w5. Here I used the boiler can to slowly bend the brass sheet to form the main support. By working the metal slowly in your hands you should be able6. I drilled a centered hole to allow my fill connector to pass thru the boiler housing. When working with thin brass like this its best to start w7. Using the boiler housing as a guide mark the location for the steam output pipe. I used a short section of copper tube which fits VERY snuggly i8. Now that we have a functioning air-tight boiler we need to support it inside the brass housing. I used small 1" wide sections of brass bent into9. As I also intend to use this boiler to run a small engine or turbine it was important that I could close off the steam supply to allow the main10. After searching around my house for a suitable container to wrap the copper heat exchanger pipes around I finally stumbled upon an old body spr STEAM BOILERS The Parker Boiler water tube design offers an extremely efficient, reliable steam boiler. The Parker Boiler water tube design offers an extremely efficient, reliable steam boiler built for the long term and ease of maintenance. The Parker Boiler design offers …
Cleaver-Brooks is the industry leader in providing energy-efficient, low-emissions boiler room products. With the power of total integration, only Cleaver-Brooks can offer a complete boiler room solution that is designed, engineered, and manufactured by one company.
Alibaba.com offers 559 hot sale vertical steam boiler products. About 97% of these are Boilers. A wide variety of hot sale vertical steam boiler options are available to you, such as usage, type.
0.4 mpa steam boiler – Steam Boiler In India. 0.4 mpa steam boiler. LMS Stanier Class 5 4-6-0 – Wikipedia2019-3-30 · The London Midland and Scottish Railway Class 5 4-6-0, almost universally known as the Black Five, is a class of steam locomotive. It was introduced by William Stanier in 1934 and 842 were built between then and 1951.
steam boilers 7-25hp pressures up to 250psi (low nox available) view 1.5-3hp view 30-50hp view 70-150hp low nox available Never A Compromise For Quality or Safety T he large horizontal steam drum provides ample steam release area to assure dry steam delivery.
Author: Tyler Wilde The saturated steam / hot water was a controlled pH of 7.0-7.5. Usually, a slightly basic pH is maintained to prevent corrosion in all such steam systems. The effects of steam on an FKM elastomer are depicted below. The failure mechanism is dehydrohalogenation despite the low level of VF2 in the elastomer.
The diverse steam boiler selection at Grainger includes high-efficiency wall-mounted condensing boilers, cast iron compact gas-fired boilers and direct-spark boilers with Energy Star ratings.
File Size: 258KB Steam drum internals for typical type of boiler are shown. The internals include separation devices to assist in separating small droplets of boiler water from the steam. Boiler water in the steam will cause scaling of the superheater and steam turbines.Baffles, chevron types separators and demister pads are used to minimize boiler water carryover.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.