Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Dec 14, 2018· When the steam condenses or the water cools, it travels back to the boiler and is reheated. Energy Usage. Both steam boilers and hot water boilers offer energy efficiency, but in different ways. A steam boiler uses more energy to boil the water, but uses less energy during the transfer of heat.
Boiler feed water pressure regulators are designed for use in commercial and residential hydronic heating systems to fill the boiler and piping system with water and maintain continuous pressure. Certain valve types also provide make-up water to the system and prevent backflow when supply pressure falls below system pressure.
Lenntech can provide you all water treatment equipment, including chemicals. Chemicals will condition the water and protect boiler equipment (heater, pump, …). Lenntech can advise you on treatments required on the make-up water, by providing calculations on mass balance in the steam boiler, contributing for lower electricity consumption.
If the boiler’s thermostat is faulty, it will allow the burners to stay on longer than it should, causing the heat exchanger to overheat. And when water comes into contact with the super hot heat exchanger, steam bubbles are created, which then erupt noisily. Water temperature on boiler is set too high. Setting your boiler to a very high
Author: ArenalesRailway The boiler receives the feed water, which consists of varying proportion of recovered condensed water (return water) and fresh water, which has been purified in varying degrees (make up water).The make-up water is usually natural water either in its raw state, or treated by some process before use.
In steam applications, water quality is an important part of boiler selection. Steam boilers tend to be steel water-tube- or fire-tube-type boilers in the 10-to-1,000-hp range. Fire-tube boilers are more robust and more tolerant of poor water quality, but require more physical space, than water-tube boilers.
The make-up water is added into the surge tank and blended with the hot condensate returns to avoid shocking the deaerator with extreme variations in water temperature and capacity. The pumps, typically referred to as transfer pumps, must run continuously.
Click to view6:38Mar 14, 2013· If you want see this steam boiler working, please visit this video: watch?v=GzpVzMvyNLw Building step to step my live steam artefact
Boiler Systems Operation. In steam heating systems, a boiler furnace heats water by means of a gas or oil-fired burner and turns it into steam. The steam travels through pipes to radiators or convectors, which give off heat and warm the room. As the steam cools, it condenses back into water, and returns to the boiler to be heated again.
Author: NOBOX7 The make up water for two Weil-Mclain 88 boilers with an output of 3100lb/hr of steam each. They run the the heat and hot water where I work and are using a lot of water because of bad traps. I wanted to replace all the traps this summer but working for the state is not like working in the real world.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.