Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Hot water heating systems need a little maintenance, like venting the radiators and draining the boiler, to keep things running efficiently. Gravity and hot water furnaces are not often installed in new homes today, but similar systems with the old cast-iron radiators throughout the house were fixtures in homes built around 1900, and some of […]
User rating: 4.8/5 Author: Bob Formisano Nov 20, 2011· Lately I've been hearing the sound of water flowing inside the pipes of my forced hot water heating system. I heard it last year too but this time it seems to be more frequent. From what I have read on the Interwebs this indicates that there is air in the pipes and that the system should be flushed.
Once a year, the entire hot water and steam system should be flushed to keep the pipes clear and the water flowing freely. To flush the system, open the blow-off valve and let the water run off into a bucket until it runs clear. If the water still looks rusty after the system has been flushed, call a …
Aqua-Hot does not recommend draining and flushing the system unless the wrong type of fluids were added to the boiler fluid. For example, if your system uses propylene glycol “GRAS” antifreeze, but ethylene glycol was mistakenly added, the system would need to be flushed for safety reasons.
File Size: 100KB May 05, 2016· 2. Turn Off Gas to Hot Water Heater. If you have a gas hot water heater, find the gas pipe leading to your thermostat and pilot light and turn the valve to the off position. If you decide to just turn your thermostat to “pilot” you won’t need to do this step. …
Mar 09, 2006· To flush a water heater, start by turning off the heater's power source using the breaker or thermostat. Next, rotate the water shut-off valve on your heater clockwise to turn off the cold water supply. Then, turn on a hot water faucet in one of your sinks or …
Mar 20, 2018· Flushing your hot water heater could be necessary as often as every few months depending on the mineral content of your local water supply. Before You Begin a Water Heater Flush Prior to draining the tank, you need to figure out how to turn off your gas water heater.
Location: 1167 Woodbine ave Suite 2, Toronto, M4C 4C6 Turn down the house thermostat to a low setting. Turn off the electrical power supply to the boiler. … Gravity Hot Water Heating Systems. A gravity hot water heating system is the oldest and simplest … Tube size Water volume Flushing and Disinfection of Hot and Cold Water Systems (litres per metre run) 15 x 0.7 0.145 22 x 0.9 0.320 28 x 0.9 0.539 35 x 1.2 0.835 42 x 1.2 1.232 54 x 1.2 2.091 66.7 x 1.2 3.247 76 x 1.5 4.197 108 x 1.5 8.659 *Specification for "Design, installation, testing and maintenance of services supplying water for domestic use
Hydronic system flushing - how often? — Heating Help: The WallCleaning and flushing hydronic system — Heating Help: The Wallhydronic system powerflush? — Heating Help: The WallTSP concentrations — Heating Help: The WallSee more results Power Flushing Service Totally Tankless offers a complete boiler system flush to clean the inside of your heating system. With the passage of time, central heating systems may develop circulation problems as a result of corrosion and sludge in areas of low flow, notably the lower central areas of radiators, and underfloor pipe work.
Cleaning hot water systems From B&Gin summary. Add 1 lb Trisodium phosphate per 50 gallons system water. Fill, vent and circulate system a few hours, drain and refill system. A little bit of cleaner will stay in system and should provide a slightly alkaline solution.shoot for a Ph of 7 to 8. Just got this info, and plan on starting to use it.
Jan 30, 2020· Once prepared, the technician will connect a power flushing machine to your heating system as per the manufacturer’s settings. All of this is performed without the new boiler attached to the system. The power flushing machine will be filled with water from your mains. This water is then pumped through your entire system for ten to twenty minutes.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.