Product Thermal Capacity: 1 - 20 t/h
Working Pressure: 0.7 - 2 Mpa
Available Fuel: Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc.
Available Industries: Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc.
WNS series horizontal internal combustion boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
1. Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
2.Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
3. Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
4. Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Reheat steam pressures are normally around 45 bar. SuperHeater / ReHeater. The above are the major water and steam circuit items in a boiler and are collectively called the ‘pressure parts’. This post is part of the series: Working Of A Power Plant Boiler. Boiler in a power plant has two functions.
Boiler efficiency and carbon burnout. Boiler efficiency is a measure of how effectively chemical energy in fuel is converted into heat energy in steam going to the turbines. The largest boiler efficiency loss is sensible heat lost as hot flue gases (and ash) exit the boiler.
- Biomass Power Plant: Turns dry wheatstraws into power in one process with our biomass power plant. Just add the wheatstraws into the reactor and top up the boiler water regularly and you are good to go. It produces 300 power when fully upgraded, run ~44% more …
Author: Learn Engineering Dipak K. Sarkar, in Thermal Power Plant, 2017. 10.1 Introduction. In a steam power plant, atmospheric air is fed into the furnace of a steam generator for combustion of fossil fuel (coal, fuel oil, and fuel gas), generating heat released by burning of fuel. Hence, it is essential that fuel is burnt completely in the furnace to release as much
Jan 15, 2019· Heat Transfer In Steam Boiler. A steam boiler is designed to absorb the maximum amount of heat released from the process of combustion. There are three way (Radiation, convection & Conduction) that heat is transfer in the boiler and relative percentage of each heat transfer within system boiler is dependent on the type of steam boiler, fuels and the designed transfer surface.
Author: Suncor Energy The energy efficiency of a conventional thermal power station is defined as saleable energy produced as a percent of the heating value of the fuel consumed. A simple cycle gas turbine achieves energy conversion efficiencies from 20 to 35%. Typical coal-based power plants operating at steam pressures of 170 bar and 570 °C run at efficiency of 35 to 38 %, with state-of-the-art fossil fuel
Keeping steam contamination at an acceptable level is a major objective of plant chemical control. The method of maintaining steam purity depends on the manner in which the steam is produced. Plants with drum-type steam generators — both conventional boilers and heat recovery steam generators (HRSGs) — maintain steam
The vibratory shearing process has two major applications in the power plant. The first is processing of boiler water influent. To avoid boiler scale, power plants usually utilize a multi-step process to remove hardness of incoming water, including either chemical treatment or ion exchange and several less advanced methods such as multimedia filtration.
Nov 24, 2019· The energy and utilities facilities at Suncor’s Base Plant supply steam, power, boiler feed water, and hot water to run operations. Currently, much of this steam comes from three petroleum coke-fired boilers originally installed in 1967. The Coke Boiler Replacement (CBR) project will see the aging units replaced with two cogeneration units.
CHAPTER 4 Steam power plants E. Khalil Department of Mechanical Power Engineering, Cairo University, Cairo, Egypt. Abstract The efﬁ cient utilization of fossil energy in power generation together with low pollution in conventional thermal power plants is a topic that is gaining interest internationally.
No. 76, Xin Da Road, Zhou tie Town, Yixing, Wuxi, China
0086-510-68530066, +86-13506151292Get Latest Price
Copyright © 2020.Zhongzheng Boiler Co., ltd. All rights reserved.